The gas supply that is used for a gas range is usually controlled by a shutoff valve. This flexible supply line is delivering the gas to the appliance. Fresh water is coming from the water supply pipes and is then distributed to the sink. The sink drain system carries that used water to sewers or septic tanks. Every kitchen plumbing system consists of these basic elements:.
If you have additional appliances in your kitchen that uses water, such as garbage disposal, dishwasher, or fridge ice maker, then these components will usually be connected underneath the sink. When installing new kitchens, these connections are usually made underneath the flooring, with the shut-off valve that is located under the sink.
Under the kitchen sink plumbing, we can find a lot of parts and pieces which are required for this system to work. The first thing we find below the sink is a rubber gasket and a locknut, that is used to hold the strainer in place and that connects it to the tailpiece. The connection of plumbing in the kitchen to the water supply and sewerage system is carried out after the completion of finishing work and the installation of kitchen furniture.
To connect the dishwasher in the kitchen, use the flexible piping elements that come with this type of plumbing. As noted earlier, to prevent the appearance of unpleasant odors, the connection to the sewer is carried out through a water seal. To avoid gurgling in the sink , it is better to use a special valve when connecting the dishwasher. The installation of a water filter is carried out in most cases in the kitchen under the sink.
Polymer and metal-polymer pipes have practically displaced traditional steel and copper products from this area due to a number of advantages. Such pipelines are not subject to corrosion, their inner layer is resistant to abrasion and does not contribute to the accumulation of deposits.
Due to this, the bore diameter of the pipe remains constant throughout its entire service life at least 50 years. It depends upon your maintenance. If you are a cleaning freak, you can use a porcelain sink and glossy plumbing products. But if you are a busy bee, it is best to go for a steel-based plumbing kit for your sink.
You should select the size of the sink and the plumbing material sizes to provide enough room for the kits to fit in. It is a complete mess if you have a moderate space for your sink allotment , but you fit in with advanced and large plumbing kits. It not only makes the draining complex but also occupies some extra room. But, you should be pre-planned on how you decide your kitchen sink to operate. You can reach your plumber for planning and fitting your kitchen sink plumbing kit.
It is more important to get a fit and tight connection based pipes for your kitchen sinks to prevent leakage. You have to remove the old drain pipes and replace them with new tailpieces connecting the drain pipe. You can cut the tailpiece based upon the need.
Then join the pipes with compression fitters and install a p-trap. Then check for leaps by filling the sink. Kitchen sink plumbing needs proper maintenance and perfectionism. Though it seems complex, with proper knowledge and adaptation techniques, you can make the plumbing works fresh and effective. Your email address will not be published. This site uses Akismet to reduce spam.
Check the fit of the sink in countertop; trim the hole with the jigsaw, if necessary. Feed the faucet's supply tubing and tailpiece through the gasket that seals the faucet to the sink and then up through the hole or holes in sink. Make sure the faucet can swing in a full arc across the sink before tightening mounting nuts.
With the sink still upside down, pack a thick roll of plumber's putty under the strainer's lip and push it up through the sink's drain hole. Slip the gasket, washer, and housing if your strainer has one onto the strainer and against the underside of sink. Dab pipe-joint compound onto its exposed threads. Thread the locknut onto the strainer by hand, then tighten it with pliers while holding the strainer in place.
Fit the gasket onto the sink-drain tailpiece and attach it to the strainer with its slip nut. Tighten the nut by hand while holding strainer. With sink still upside down, squeeze a bead of silicone caulk around the underside of the sink's lip. Check that the front of the sink is parallel with the front edge of countertop. Adjust it, if necessary. Connect the faucet to shut-off valves using acorn-head supply tubes or braided stainless steel hoses.
Cut and dry-fit lengths of PVC pipe to connect the trap adapter to the trap and the drain elbow to the waste line. Swivel the trap or slide it on the tailpiece to fine-tune the pipes' lengths and alignment.
Take the drain pieces apart. Clean off the cut ends with a utility knife. Coat them and their mating pieces with PVC primer. Let dry. Swab PVC cement on both ends being joined. Immediately push pieces together. Hold for 30 seconds. Attach the dishwasher drain line to the waste nib of the tailpiece.
0コメント